Super Purchasing for Nylon Wall Anchor Wholesale to Malta
Plastic Wall Anchor 1. Material Options PE, PA, Nylon 2. Color Options Grey, white, yellow, red, blue, green Semi transparent Transparent 3. Size Available M6, M8, M10, M12, M16 (screw size) Length: 20 to 120mm Separately sold or assorted with screws/nails 4. Model Type Swing shape Conical shape 5. Packing Options Polybag bulk packed with carton Small Color box Blister Card Assorted tool box
Super Purchasing for Nylon Wall Anchor Wholesale to Malta Detail:
Plastic Wall Anchor
1. Material Options
PE, PA, Nylon
2. Color Options
Grey, white, yellow, red, blue, green
3. Size Available
M6, M8, M10, M12, M16 (screw size)
Length: 20 to 120mm
Separately sold or assorted with screws/nails
4. Model Type
5. Packing Options
Polybag bulk packed with carton
Small Color box
Assorted tool box
Product detail pictures:
Our solutions are widely identified and trusted by people and might fulfill continuously transforming economic and social demands for Super Purchasing for Nylon Wall Anchor Wholesale to Malta, The product will supply to all over the world, such as: Las Vegas , French , Liechtenstein , Due to our strict pursues in quality, and after-sale service, our product gets more and more popular around the world. Many clients came to visit our factory and place orders. And there are also many foreign friends who came for sight seeing, or entrust us to buy other stuff for them. You are most welcome to come to China, to our city and to our factory!
The laying of a wooden floor is only possible if the window and door frames have been fitted in order to waterproof the area and prevent any excess humidity.
The concrete sub-floor must be clean, and free of dust or any other foreign substances such as any residual lime, plasterwork or similar.
The concrete sub-floor should be evenly compressed. When the surface is hit with a mallet weighing 750 g, no visible marks should be left nor should there be any crumbling or dust particles forming. It is important to check the surface strength of the sub-floor by scratching it with a suitable iron nail to form a series of squares. No deep cracks, or crumbling or dust formation should occur.
It is essential that the residual humidity of the sub-floor is no more than 2% on concrete sub-floors and 0,5% on anhydride sub-floors. To remedy any increases in the humidity the sub-floor is always placed on a moisture screen (higher floors) or a vapour barrier (on the ground floor or above the basement). Use an electric hygrometer to determine which part of the sub-floor has the highest levels of humidity, and in this point carry out a measurement with a carbide hygrometer. Extract a sample with a hammer and chisel which is representative of the entire thickness of the sub-floor discarding the surface level for at least 15 mm. Weigh the broken-up and mixed-up sample using a small set of accurately calibrated scales, taking care that the sample is not in contact with the air for too long.
Place several steel balls a phial of pre-calibrated calcium carbide and the sample of extracted sub-floor into the designated container. Close the container with the a suitable lid equipped with a manometer and check the gasket, shake vigorously for 5 minutes and wait for the pressure to stabilize (within approximately 15 minutes) before taking the manometer reading. If the reading reveals a percentage of humidity that is greater than it is necessary to carry out a precautionary treatment of the sub-floor with a suitable primer.
The laying of the parquet is only possible if the room temperature is no less than 15°C. The relative air humidity should be measured with a suitable instrument and should be approximately 50%.
In addition it is necessary to measure the humidity of the wood to be laid with an electric hygrometer, testing at least four or five sample pieces. The level of humidity must be between 7 and 11 %.
By Cindy 2016-3-16 11:41
The goods we received and the sample sales staff display to us have the same quality, it is really a creditable manufacturer.
By Nana 2016-9-13 12:37